Commercial Plumbing Services in Canton, OH

Installed approximately 25 feet of interior gas piping to supply new gas appliance. Routed black iron pipe through designated interior pathways, made all necessary connections, and pressure tested system to verify integrity and compliance with code requirements.

Responded to water leak emergency involving bathtub drain leaking through ceiling into room below. Upon inspection, discovered tub faucet would not shut off completely and no isolation shut-off valves were present at fixture. Documented extensive water damage to ceiling with compromised drywall and exposed cavity, as well as corroded supply valve connections at wall penetrations showing significant rust and deterioration. Photographed damaged areas and plumbing conditions for assessment and repair planning.

Responded to follow-up call for persistent toilet leak affecting kitchen ceiling below. Upon inspection of basement/crawl space area beneath fixture, identified active leak at elbow fitting connection in drainage system. Previous toilet reset had not resolved the issue as the leak source was determined to be at the bent elbow joint in the waste line. Documented existing water damage to floor joists and structural components with visible staining and discoloration from ongoing moisture intrusion.

Installed 10 feet of gas piping with tap location positioned outside the structure. Permit obtained through Stark County as required for this gas line installation, with all work completed to code specifications and ready for inspection.

Replaced a section of the main drain stack with 4" PVC pipe in the basement. Cut access through the back of the lavatory cabinet to tie the 1½" PVC lav drain line into the vent system and connect to the new stack. Installed a new lift and turn tub shoe assembly to properly tie in the bathtub drain. Snaked the kitchen sink drain line from the basement cleanout to clear the blockage. Replaced both straight stop angle valves to ensure proper water supply shutoff capability.

Removed existing conventional water heater and installed new wall-mounted tankless water heater unit in basement utility area. Installation included mounting unit to masonry wall, connecting copper supply and return lines with appropriate shut-off valves and fittings, installing black gas supply line with proper connections, and routing white PVC exhaust venting system through ceiling with T-junction configuration for proper combustion gas exhaust. Verified all connections for leaks, confirmed proper gas flow, tested unit operation, and ensured Energy Star certified system was functioning correctly with digital controls operational.

Replaced deteriorated cast iron stack from second floor to basement with 4" PVC pipe and fittings. Installation included proper drainage configuration with P-trap assembly in attic space and vertical drain line through floor joists to basement level. All connections secured to structural elements per code requirements, utilizing appropriate couplings and elbow fittings to ensure proper flow and venting.

Completed comprehensive plumbing inspection focusing on lead pipe assessment throughout the property. Inspected exposed basement plumbing infrastructure, identifying copper piping with visible corrosion and verdigris buildup at connection points near ceiling joists, along with mixed pipe materials including PVC drainage lines. Documented existing plumbing conditions and provided estimate for potential lead pipe replacement where applicable.

Installed 10 feet of new gas piping to an exterior tap location. The installation included proper connections to the existing gas meter system with appropriate fittings and valves to ensure safe operation. All piping was secured and tested for leaks in accordance with code requirements.

Installed 10 feet of gas piping with exterior tap location, connecting to manifold-style valve assembly mounted on building exterior. System features multiple blue-painted valves and connection points for proper gas distribution, with all components secured to brick wall per code requirements.

Replaced one 1-inch brass backflow prevention device on the building's main water supply line. Installed new reduced pressure zone (RPZ) assembly with dual green-handled ball valves for isolation and system maintenance. Connected pressure gauge with brass fittings to monitor differential pressure across the backflow preventer. Configured blue test port tubing for required annual testing and certification. Mounted all components securely to wall and verified proper orientation of the backflow device. Tested system operation, confirmed all valves function correctly, and ensured no leaks at compression joints or threaded connections.

Responded to service call for bathroom faucet repair and sewer line inspection. Replaced broken faucet handle in bathroom fixture. Inspected exposed plumbing infrastructure including copper supply lines, brass valve assembly, and drainage piping from sink to basement level. Assessed condition of aging plumbing components, noted water staining on surrounding wall surfaces, and verified proper operation of drainage system and HVAC condensate lines in basement area.

Completed a 10-foot exterior sanitary sewer lateral repair requiring excavation and permit compliance. Removed damaged section of sewer line and installed new white PVC pipe on a properly graded gravel bed for drainage support. Backfilled excavation and coordinated inspection scheduling to ensure all work met local plumbing code requirements.

Ordered and awaiting delivery of parts required to install a meter horn assembly for a 5/8" water meter in a basement utility area with aging plumbing infrastructure. Upon arrival of components, will complete the installation of the meter horn to the existing copper pipe system, ensuring proper integration with the water meter and compliance with plumbing code requirements.

Responded to water leak at main water line valve assembly located near wash sink area. Upon inspection, identified steady drip originating from aged plumbing assembly mounted on utility room wall, consisting of ball valves with blue handles, pressure regulator, water meter, and multiple threaded pipe connections showing significant weathering and oxidation. Documented existing conditions with detailed photographs of the complete valve assembly, backflow preventer, and associated piping components for assessment. Assembly displayed greenish-gray patina on brass and copper fittings, indicating long-term exposure to moisture. Prepared two required quotes as specified: first for like-for-like repairs to address the leak at the main valve connection, and second for comprehensive system evaluation. Photographs captured all plumbing components including valve positions, meter assembly, electrical junction box connections, and drain pan placement for proposal approval and documentation purpose

Performed hydro-jetting service on interior floor drain system. Cleared drain line using high-pressure water jetting equipment to remove blockages and restore proper drainage flow. Service completed as requested with drain now functioning properly.

Performed camera inspection and jetting service on commercial kitchen drain line serving sandwich preparation station experiencing backup issues when sink was drained. Conducted video inspection to identify blockage location and condition of drain line, followed by hydro-jetting to clear obstruction and restore proper drainage flow. Documented equipment conditions and water damage present in affected areas, with visible moisture and staining observed on flooring surfaces near HVAC equipment and cabinet installations.

Responded to service call for disconnected sewer drain piping exiting the side of the house. Upon arrival, excavated and exposed the main line where white PVC pipe sections had become separated. Reconnected the pipes using proper coupling fittings to restore the 90-degree elbow joint configuration, ensuring secure connection between horizontal and vertical pipe sections. Verified proper alignment and functionality of the repaired sewer drain system.

Responded to vacant unit requiring meter horn installation to facilitate water service restoration by municipal utility. Upon arrival, accessed property via lockbox and located water meter assembly in deteriorated basement/crawl space area showing extensive water damage and long-term neglect. Installed new meter horn on existing water meter per code requirements to allow city water department to restore service to the property. Completed installation using appropriate fittings and connections to integrate with existing white PVC supply piping and corroded gate valve assembly. Verified proper alignment and secure mounting of meter horn component to meet municipal inspection standards for service reconnection.

Responded to emergency call for basement flooding caused by main drain backup. Upon arrival, found significant standing water throughout basement storage area with muddy sediment covering entire floor surface. Accessed garage floor drain cleanout and performed large-capacity drain snaking procedure to clear main line obstruction. Successfully removed blockage and restored proper drainage flow. Verified system functionality and confirmed water began receding from affected area. Documented pre-existing flood damage to basement contents including furniture, storage containers, and various household items. Photographed flooded conditions and exposed basement infrastructure including plumbing lines, HVAC ductwork, and spray foam insulation applications on overhead systems.